Power Quality Analysers

			Fluke 435 series ii 3 phase power quality analyser Power inverter efficiency: Simultaneously measure AC output power and DC input power for power electronics systems using optional DC clamp. PowerWave data capture: Capture fast RMS data, show half-cycle and waveforms to characterize electrical system dynamics Energy loss calculator: Classic active and reactive power measurements, unbalance and harmonic power, are quantified to energy losses. Highest safety rating in the industry: 600 V CAT IV/1000 V CAT III rated for use at the service entrance. Measure all three phases and neutral: With included four flexible current probes with enhanced thin flex design to fit into the tightest places. System-Monitor: Ten power quality parameters on one screen according to EN50160 power quality standard. Logger function: Configure for any test condition with memory for up to 600 parameters at user defined intervals. View graphs and generate reports: With included analysis software. Battery life: Seven hours operating time per charge on Li-ion battery pack
			Fluke 434 series ii 3 phase power quality analyser Energy loss calculator: Classic active and reactive power measurements, unbalance and harmonic power, are quantified to pinpoint energy losses. Troubleshoot real-time: Analyze the trends using the cursors and zoom tools. Highest safety rating in the industry: 600 V CAT IV/1000 V CAT III rated for use at the service entrance. Measure all three phases and neut ral: With included four flexible current probes with enhanced thin flex design to fit into the tightest places. Automatic Trending: Every measurement is always automatically recorded, without any set-up. System-Monitor: Ten power quality parameters on one screen according to EN50160 power quality standard. Logger function: Configure for any test condition with memory for up to 600 parameters at user defined intervals. View graphs and generate reports: With included analysis software. Battery life: Seven hours operating time per charge on Li-ion battery pack
			Fluke 437 series ii 400Hz, 3Phase Power quality analyser Power inverter efficiency: Simultaneously measure AC output power and DC input power for power electronics systems using optional DC clamp. PowerWave data capture: Capture fast RMS data, show half-cycle and waveforms to characterize electrical system dynamics Energy loss calculator: Classic active and reactive power measurements, unbalance and harmonic power, are quantified to energy losses. Highest safety rating in the industry: 600 V CAT IV/1000 V CAT III rated for use at the service entrance. Measure all three phases and neutral: With included four flexible current probes with enhanced thin flex design to fit into the tightest places. System-Monitor: Ten power quality parameters on one screen according to EN50160 power quality standard. Logger function: Configure for any test condition with memory for up to 600 parameters at user defined intervals. View graphs and generate reports: With included analysis software. Battery life: Seven hours operating time per charge on Li-ion battery pack
			Fluke 438 series ii 3 phase Power Quality Analyser with Motor Analysis Measure key parameters on direct-on-line motors including torque, RPM, mechanical power and motor efficiency Calculate mechanical power and efficiency without the need of mechanical sensors Measure electrical power parameters such as voltage, current, power, apparent power, power factor, harmonic distortion and unbalance to identify charateristics that impact motor efficiency Waveform capture function, captures 100/120 cycles of each event detected Has all the advanced power quality functions of the Fluke 430 series ii Power quality analysers

			Fluke 345 Single phase Power Quality ClampMeter AC/DC current: Clamp-on measurement of ac current up to 1400 A rms and dc current up to 2000 A without breaking the circuit Highest safety rating: 600 V CAT IV power analyzer is rated for use at the service entrance Accurate in noisy environments: Clamp meter performs even with distorted waveforms present on electronic loads with low-pass filter Data logging: Identify intermittent faults by logging any power quality parameter for minutes, or over a month, including harmonics Verify batteries: Direct measurement of dc ripple (%) for battery and dc systems Troubleshoot harmonics: Analyze and log harmonics digitally or graphically Inrush current: Capture and analyze nuisance tripping, from 3 seconds to 300 seconds Easy to use: Easily confirm power meter setup with large backlit color display of waveforms and trends 3-Phase power: Built in capability for balanced loads View graphs and generate reports: Use power analyzer with included Power Log software



			Fluke 1732 Three Phase Electrical Energy Logger Measure all 3 phases with included flexible probes (3 included) Bright Colour Touch screen Complete in the field setup through the front panel Fully integrated Energy Logging Energy Analyse plus application software included Optional module to enable Fluke Connect to allow for measurements to be captured onto your apple or Android device
			Fluke 1736 Three Phase Power Logger Measure all three phases and neutral with included 4 flexible current probes Comprehensive logging where more than 20 logging sessions can be stored Capture dips, swells and inrush currents Optimized user interface with guided graphical setup Fluke Connect compatible to allow for measurements to be captured with your Apple or Android device
			Fluke 1738 Three Phase Power Logger Measure all three phases and neutral with included 4 flexible current probes Comprehensive Logging where more than 20 logging sessions can be stored Capture dips, swells and inrush current and event waveform Optimized user interface with guided graphical setup Fluke Connect Compatible to allow for measurements to be captured with your Apple or Android device